diff --git a/include/configs/km/km-mpc8309.h b/include/configs/km/km-mpc8309.h
new file mode 100644
index 0000000..e89b7af
--- /dev/null
+++ b/include/configs/km/km-mpc8309.h
@@ -0,0 +1,137 @@
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 family */
+#define CONFIG_QE		1	/* Has QE */
+
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR   0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0			\
+		| SICR_1_UART1_UART1RTS		\
+		| SICR_1_I2C_CKSTOP		\
+		| SICR_1_IRQ_A_IRQ		\
+		| SICR_1_IRQ_B_IRQ		\
+		| SICR_1_GPIO_A_GPIO		\
+		| SICR_1_GPIO_B_GPIO		\
+		| SICR_1_GPIO_C_GPIO		\
+		| SICR_1_GPIO_D_GPIO		\
+		| SICR_1_GPIO_E_GPIO		\
+		| SICR_1_GPIO_F_GPIO		\
+		| SICR_1_USB_A_UART2S		\
+		| SICR_1_USB_B_UART2RTS		\
+		| SICR_1_FEC1_FEC1		\
+		| SICR_1_FEC2_FEC2		\
+		)
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0			\
+		| SICR_2_FEC3_FEC3		\
+		| SICR_2_HDLC1_A_HDLC1		\
+		| SICR_2_ELBC_A_LA		\
+		| SICR_2_ELBC_B_LCLK		\
+		| SICR_2_HDLC2_A_HDLC2		\
+		| SICR_2_USB_D_GPIO		\
+		| SICR_2_PCI_PCI		\
+		| SICR_2_HDLC1_B_HDLC1		\
+		| SICR_2_HDLC1_C_HDLC1		\
+		| SICR_2_HDLC2_B_GPIO		\
+		| SICR_2_HDLC2_C_HDLC2		\
+		| SICR_2_QUIESCE_B		\
+		)
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1  0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_PZ_MAXZ | \
+	DDRCDR_NZ_MAXZ | \
+	DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+					 SDRAM_CFG_32_BE | \
+					 SDRAM_CFG_SREN | \
+					 SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ODT_RD_NEVER | \
+					 CSCONFIG_ODT_WR_ONLY_CURRENT | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE	0x47860242
+#define CONFIG_SYS_DDR_MODE2	0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+				 (0 << TIMING_CFG0_WWT_SHIFT) | \
+				 (0 << TIMING_CFG0_RRT_SHIFT) | \
+				 (0 << TIMING_CFG0_WRT_SHIFT) | \
+				 (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+				 (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM		2       /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR	0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
diff --git a/include/configs/km/km-mpc832x.h b/include/configs/km/km-mpc832x.h
new file mode 100644
index 0000000..3c2173d
--- /dev/null
+++ b/include/configs/km/km-mpc832x.h
@@ -0,0 +1,91 @@
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE	/* Has QE */
+#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define CONFIG_83XX_PCICLK		66000000
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define UEC_VERBOSE_DEBUG	1
+
+#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_PZ_MAXZ | \
+	DDRCDR_NZ_MAXZ | \
+	DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+					 SDRAM_CFG_32_BE | \
+					 SDRAM_CFG_SREN | \
+					 SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ODT_WR_CFG | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE	0x47860242
+#define CONFIG_SYS_DDR_MODE2	0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+				 (0 << TIMING_CFG0_WWT_SHIFT) | \
+				 (0 << TIMING_CFG0_RRT_SHIFT) | \
+				 (0 << TIMING_CFG0_WRT_SHIFT) | \
+				 (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+				 (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
diff --git a/include/configs/km/km-mpc8360.h b/include/configs/km/km-mpc8360.h
new file mode 100644
index 0000000..8f26e05
--- /dev/null
+++ b/include/configs/km/km-mpc8360.h
@@ -0,0 +1,91 @@
+/* KMBEC FPGA (PRIO) */
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	64
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE			/* Has QE */
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define UEC_VERBOSE_DEBUG	1
+
+#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+
+/*
+ * System IO Setup
+ */
+#define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
+
+/**
+ * DDR RAM settings
+ */
+#define CONFIG_SYS_DDR_SDRAM_CFG (\
+	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+	SDRAM_CFG_SREN | \
+	SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+
+#define CONFIG_SYS_DDR_CLK_CNTL (\
+	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CONFIG_SYS_DDR_INTERVAL (\
+	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_Q_DRN)
+#define CONFIG_SYS_DDR_MODE		0x47860452
+#define CONFIG_SYS_DDR_MODE2		0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 (\
+	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+	(0 << TIMING_CFG0_WWT_SHIFT) | \
+	(0 << TIMING_CFG0_RRT_SHIFT) | \
+	(0 << TIMING_CFG0_WRT_SHIFT) | \
+	(0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 (\
+	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+	(5 << TIMING_CFG2_CPO_SHIFT) | \
+	(0 << TIMING_CFG2_ADD_LAT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3			0x00000000
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
+
+/*
+ * PAXE on the local bus CS3
+ */
+#define CONFIG_SYS_PAXE_BASE		0xA0000000
+#define CONFIG_SYS_PAXE_SIZE		256
diff --git a/include/configs/km/km-mpc83xx.h b/include/configs/km/km-mpc83xx.h
new file mode 100644
index 0000000..455e523
--- /dev/null
+++ b/include/configs/km/km-mpc83xx.h
@@ -0,0 +1,160 @@
+/*
+ * Internal Definitions
+ */
+#define BOOTFLASH_START	0xF0000000
+
+#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
+
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
+					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CFG_83XX_DDR_USES_CS0
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_DDR_II
+#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_FLASH_BASE		0xF0000000
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+/* Reserve 768 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Size  Device
+ * ---- ---     ------- ------  -----  ------
+ *  0   Local   GPCM    16 bit  256MB FLASH
+ *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
+ *
+ */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES	4
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	200000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	200000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+		{1, {I2C_NULL_HOP} } }
+
+#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
+
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
+
+/*
+ * Environment
+ */
+
+#ifndef CONFIG_SYS_RAMBOOT
+#ifndef CONFIG_ENV_ADDR
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+					CONFIG_SYS_MONITOR_LEN)
+#endif
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
+#ifndef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
+#endif
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+						CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#else /* CFG_SYS_RAMBOOT */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif /* CFG_SYS_RAMBOOT */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
+#define CONFIG_KM_DEF_ENV "km-common=empty\0"
+#endif
+
+#ifndef CONFIG_KM_DEF_ARCH
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	CONFIG_KM_DEF_ENV						 \
+	CONFIG_KM_DEF_ARCH						 \
+	"newenv="							 \
+		"prot off " __stringify(CONFIG_ENV_ADDR) " +0x40000 && " \
+		"era " __stringify(CONFIG_ENV_ADDR) " +0x40000\0"	 \
+	"unlock=yes\0"							 \
+	""
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"UEC0"
diff --git a/include/configs/kmcoge5ne.h b/include/configs/kmcoge5ne.h
index 847996f..fc78b27c 100644
--- a/include/configs/kmcoge5ne.h
+++ b/include/configs/kmcoge5ne.h
@@ -8,10 +8,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* KMBEC FPGA (PRIO) */
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	64
-
 #define CONFIG_HOSTNAME		"kmcoge5ne"
 #define CONFIG_KM_BOARD_NAME	"kmcoge5ne"
 #define CONFIG_KM_DEF_NETDEV	"netdev=eth1\0"
@@ -24,14 +20,11 @@
 #define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
 #define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE			/* Has QE */
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
 
 /*
  * System Clock Setup
@@ -40,201 +33,6 @@
 #define CONFIG_SYS_CLK_FREQ		66000000
 #define CONFIG_83XX_PCICLK		66000000
 
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Setup
- */
-#define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
-
-/**
- * DDR RAM settings
- */
-#define CONFIG_SYS_DDR_SDRAM_CFG (\
-	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-	SDRAM_CFG_SREN | \
-	SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-
 /**
  * KMCOGE5NE has 512 MB RAM
  */
@@ -246,68 +44,12 @@
 	CSCONFIG_ROW_BIT_13 | \
 	CSCONFIG_COL_BIT_10)
 
-#define CONFIG_SYS_DDR_CLK_CNTL (\
-	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_DDR_INTERVAL (\
-	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_Q_DRN)
-#define CONFIG_SYS_DDR_MODE		0x47860452
-#define CONFIG_SYS_DDR_MODE2		0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 (\
-	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-	(0 << TIMING_CFG0_WWT_SHIFT) | \
-	(0 << TIMING_CFG0_RRT_SHIFT) | \
-	(0 << TIMING_CFG0_WRT_SHIFT) | \
-	(0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 (\
-	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-	(5 << TIMING_CFG2_CPO_SHIFT) | \
-	(0 << TIMING_CFG2_ADD_LAT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3			0x00000000
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-
-/*
- * PAXE on the local bus CS3
- */
-#define CONFIG_SYS_PAXE_BASE		0xA0000000
-#define CONFIG_SYS_PAXE_SIZE		256
-
-
 /*
  * BFTIC3 on the local bus CS4
  */
 #define CONFIG_SYS_BFTIC3_BASE			0xB0000000
 #define CONFIG_SYS_BFTIC3_SIZE			256
 
-
 /* enable POST tests */
 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS)
 #define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
index 290108d..bfa7ca2 100644
--- a/include/configs/kmeter1.h
+++ b/include/configs/kmeter1.h
@@ -8,277 +8,23 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* KMBEC FPGA (PRIO) */
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	64
-
 #define CONFIG_HOSTNAME		"kmeter1"
 #define CONFIG_KM_BOARD_NAME   "kmeter1"
 #define CONFIG_KM_DEF_NETDEV	"netdev=eth2\0"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE			/* Has QE */
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8360.h"
 
 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Setup
- */
-#define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)
-
-/**
- * DDR RAM settings
- */
-#define CONFIG_SYS_DDR_SDRAM_CFG (\
-	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-	SDRAM_CFG_SREN | \
-	SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
 
 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
 					 CSCONFIG_ROW_BIT_13 | \
 					 CSCONFIG_COL_BIT_10 | \
 					 CSCONFIG_ODT_WR_ONLY_CURRENT)
-
-#define CONFIG_SYS_DDR_CLK_CNTL (\
-	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_DDR_INTERVAL (\
-	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_Q_DRN)
-#define CONFIG_SYS_DDR_MODE		0x47860452
-#define CONFIG_SYS_DDR_MODE2		0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 (\
-	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-	(0 << TIMING_CFG0_WWT_SHIFT) | \
-	(0 << TIMING_CFG0_RRT_SHIFT) | \
-	(0 << TIMING_CFG0_WRT_SHIFT) | \
-	(0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 (\
-	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-	(5 << TIMING_CFG2_CPO_SHIFT) | \
-	(0 << TIMING_CFG2_ADD_LAT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3			0x00000000
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-
-/*
- * PAXE on the local bus CS3
- */
-#define CONFIG_SYS_PAXE_BASE		0xA0000000
-#define CONFIG_SYS_PAXE_SIZE		256
-
-
 #endif /* CONFIG */
diff --git a/include/configs/kmopti2.h b/include/configs/kmopti2.h
index f1b7c2f..67e864f 100644
--- a/include/configs/kmopti2.h
+++ b/include/configs/kmopti2.h
@@ -26,292 +26,10 @@
 #define CONFIG_KM_BOARD_NAME	"kmopti2"
 #define CONFIG_HOSTNAME		"kmopti2"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
-/*
- * Configuration for C2 on the local bus
- */
-
-
-/*
- * Configuration for C3 on the local bus
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/kmsupx5.h b/include/configs/kmsupx5.h
index 0dd7420..ba33e60 100644
--- a/include/configs/kmsupx5.h
+++ b/include/configs/kmsupx5.h
@@ -26,283 +26,10 @@
 #define CONFIG_KM_BOARD_NAME	"kmsupx5"
 #define CONFIG_HOSTNAME		"kmsupx5"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h
index 8f9bbef..701eb53 100644
--- a/include/configs/kmtegr1.h
+++ b/include/configs/kmtegr1.h
@@ -33,340 +33,13 @@
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
 #define NAND_MAX_CHIPS				1
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 family */
-#define CONFIG_QE		1	/* Has QE */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-/* between the u-boot partition and env */
-#ifndef CONFIG_SYS_QE_FW_ADDR
-#define CONFIG_SYS_QE_FW_ADDR   0xF00C0000
-#endif
-
-/*
- * System IO Config
- */
-/* 0x14000180 SICR_1 */
-#define CONFIG_SYS_SICRL (0			\
-		| SICR_1_UART1_UART1RTS		\
-		| SICR_1_I2C_CKSTOP		\
-		| SICR_1_IRQ_A_IRQ		\
-		| SICR_1_IRQ_B_IRQ		\
-		| SICR_1_GPIO_A_GPIO		\
-		| SICR_1_GPIO_B_GPIO		\
-		| SICR_1_GPIO_C_GPIO		\
-		| SICR_1_GPIO_D_GPIO		\
-		| SICR_1_GPIO_E_GPIO		\
-		| SICR_1_GPIO_F_GPIO		\
-		| SICR_1_USB_A_UART2S		\
-		| SICR_1_USB_B_UART2RTS		\
-		| SICR_1_FEC1_FEC1		\
-		| SICR_1_FEC2_FEC2		\
-		)
-
-/* 0x00080400 SICR_2 */
-#define CONFIG_SYS_SICRH (0			\
-		| SICR_2_FEC3_FEC3		\
-		| SICR_2_HDLC1_A_HDLC1		\
-		| SICR_2_ELBC_A_LA		\
-		| SICR_2_ELBC_B_LCLK		\
-		| SICR_2_HDLC2_A_HDLC2		\
-		| SICR_2_USB_D_GPIO		\
-		| SICR_2_PCI_PCI		\
-		| SICR_2_HDLC1_B_HDLC1		\
-		| SICR_2_HDLC1_C_HDLC1		\
-		| SICR_2_HDLC2_B_GPIO		\
-		| SICR_2_HDLC2_C_HDLC2		\
-		| SICR_2_QUIESCE_B		\
-		)
-
-/* GPR_1 */
-#define CONFIG_SYS_GPR1  0x50008060
-
-#define CONFIG_SYS_GP1DIR 0x00000000
-#define CONFIG_SYS_GP1ODR 0x00000000
-#define CONFIG_SYS_GP2DIR 0xFF000000
-#define CONFIG_SYS_GP2ODR 0x00000000
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_RD_NEVER | \
-					 CSCONFIG_ODT_WR_ONLY_CURRENT | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8309.h"
 
 /* must be after the include because KMBEC_FPGA is otherwise undefined */
 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
 
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  2   Local   UPMA    16 bit  256MB APP1
- *  3   Local   GPCM    16 bit  256MB APP2
- *
- */
-
-
-/* ethernet port connected to piggy (UEC2) */
-#define CONFIG_HAS_ETH1
-#define CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM		2       /* UCC3 */
-#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK12
-#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR	0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
-
 #endif /* __CONFIG_H */
diff --git a/include/configs/kmtepr2.h b/include/configs/kmtepr2.h
index b77219f..e0c907d 100644
--- a/include/configs/kmtepr2.h
+++ b/include/configs/kmtepr2.h
@@ -26,284 +26,10 @@
 #define CONFIG_KM_BOARD_NAME    "kmtepr2"
 #define CONFIG_HOSTNAME         "kmtepr2"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h
index 785475e..6e5d507 100644
--- a/include/configs/kmvect1.h
+++ b/include/configs/kmvect1.h
@@ -25,328 +25,11 @@
 /* at end of uboot partition, before env */
 #define CONFIG_SYS_QE_FW_ADDR   0xF00B0000
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 family */
-#define CONFIG_QE		1	/* Has QE */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-/* between the u-boot partition and env */
-#ifndef CONFIG_SYS_QE_FW_ADDR
-#define CONFIG_SYS_QE_FW_ADDR   0xF00C0000
-#endif
-
-/*
- * System IO Config
- */
-/* 0x14000180 SICR_1 */
-#define CONFIG_SYS_SICRL (0			\
-		| SICR_1_UART1_UART1RTS		\
-		| SICR_1_I2C_CKSTOP		\
-		| SICR_1_IRQ_A_IRQ		\
-		| SICR_1_IRQ_B_IRQ		\
-		| SICR_1_GPIO_A_GPIO		\
-		| SICR_1_GPIO_B_GPIO		\
-		| SICR_1_GPIO_C_GPIO		\
-		| SICR_1_GPIO_D_GPIO		\
-		| SICR_1_GPIO_E_GPIO		\
-		| SICR_1_GPIO_F_GPIO		\
-		| SICR_1_USB_A_UART2S		\
-		| SICR_1_USB_B_UART2RTS		\
-		| SICR_1_FEC1_FEC1		\
-		| SICR_1_FEC2_FEC2		\
-		)
-
-/* 0x00080400 SICR_2 */
-#define CONFIG_SYS_SICRH (0			\
-		| SICR_2_FEC3_FEC3		\
-		| SICR_2_HDLC1_A_HDLC1		\
-		| SICR_2_ELBC_A_LA		\
-		| SICR_2_ELBC_B_LCLK		\
-		| SICR_2_HDLC2_A_HDLC2		\
-		| SICR_2_USB_D_GPIO		\
-		| SICR_2_PCI_PCI		\
-		| SICR_2_HDLC1_B_HDLC1		\
-		| SICR_2_HDLC1_C_HDLC1		\
-		| SICR_2_HDLC2_B_GPIO		\
-		| SICR_2_HDLC2_C_HDLC2		\
-		| SICR_2_QUIESCE_B		\
-		)
-
-/* GPR_1 */
-#define CONFIG_SYS_GPR1  0x50008060
-
-#define CONFIG_SYS_GP1DIR 0x00000000
-#define CONFIG_SYS_GP1ODR 0x00000000
-#define CONFIG_SYS_GP2DIR 0xFF000000
-#define CONFIG_SYS_GP2ODR 0x00000000
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_RD_NEVER | \
-					 CSCONFIG_ODT_WR_ONLY_CURRENT | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  2   Local   UPMA    16 bit  256MB APP1
- *  3   Local   GPCM    16 bit  256MB APP2
- *
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc8309.h"
 
 #define CONFIG_SYS_MAMR	(MxMR_GPL_x4DIS | \
 			 0x0000c000 | \
@@ -375,15 +58,4 @@
 #define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
 
-/* ethernet port connected to piggy (UEC2) */
-#define CONFIG_HAS_ETH1
-#define CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM		2       /* UCC3 */
-#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK12
-#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR	0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
-
 #endif /* __CONFIG_H */
diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h
index 456cd9d..1705f9c 100644
--- a/include/configs/suvd3.h
+++ b/include/configs/suvd3.h
@@ -21,285 +21,13 @@
  */
 
 #define CONFIG_HOSTNAME		"suvd3"
-#define CONFIG_KM_BOARD_NAME   "suvd3"
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
+#define CONFIG_KM_BOARD_NAME	"suvd3"
 
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE	0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  2   Local   UPMA    16 bit  256MB APP1
- *  3   Local   GPCM    16 bit  256MB APP2
- *
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #define CONFIG_SYS_MAMR	(MxMR_GPL_x4DIS | \
 			 0x0000c000 | \
diff --git a/include/configs/tuge1.h b/include/configs/tuge1.h
index 01d8d6b..808538e 100644
--- a/include/configs/tuge1.h
+++ b/include/configs/tuge1.h
@@ -26,283 +26,10 @@
 #define CONFIG_KM_BOARD_NAME	"tuge1"
 #define CONFIG_HOSTNAME		"tuge1"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/tuxx1.h b/include/configs/tuxx1.h
index 15a69ce..0eb673a 100644
--- a/include/configs/tuxx1.h
+++ b/include/configs/tuxx1.h
@@ -26,285 +26,11 @@
 #define CONFIG_KM_BOARD_NAME	"tuxx1"
 #define CONFIG_HOSTNAME		"tuxx1"
 
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"
-
-/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN		66000000
-#define CONFIG_SYS_CLK_FREQ		66000000
-#define CONFIG_83XX_PCICLK		66000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE		2048 /* MB */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE		0xF0000000
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/* Reserve 768 kB for Mon */
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-
-/*
- * Init Local Bus Memory Controller:
- *
- * Bank Bus     Machine PortSz  Size  Device
- * ---- ---     ------- ------  -----  ------
- *  0   Local   GPCM    16 bit  256MB FLASH
- *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
- *
- */
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME		"UEC0"
-
-#define CONFIG_UEC_ETH1		/* GETH1 */
-#define UEC_VERBOSE_DEBUG	1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
-#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-					CONFIG_SYS_MONITOR_LEN)
-#endif
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
-#ifndef CONFIG_ENV_OFFSET
-#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
-#endif
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-						CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-#else /* CFG_SYS_RAMBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE		0x2000
-#endif /* CFG_SYS_RAMBOOT */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_NUM_I2C_BUSES	4
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	200000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	200000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-		{1, {I2C_NULL_HOP} } }
-
-#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-/*
- * Internal Definitions
- */
-#define BOOTFLASH_START	0xF0000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	"newenv="							\
-		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
-		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
-	"unlock=yes\0"							\
-	""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Init Local Bus Memory Controller:
- *				      Device on board
- * Bank Bus     Machine PortSz Size   TUDA1  TUXA1  TUGE1   KMSUPX4 KMOPTI2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  PAXG   LPXF   PAXI    LPXF    PAXE
- *  3   Local   GPCM    8 bit  256MB  PINC3  PINC2  unused  unused  OPI2(16 bit)
- *
- *				      Device on board (continued)
- * Bank Bus     Machine PortSz Size   KMTEPR2
- * -----------------------------------------------------------------------------
- *  2   Local   GPCM    8 bit  256MB  NVRAM
- *  3   Local   GPCM    8 bit  256MB  TEP2 (16 bit)
- */
-
-
+#include "km/km-mpc83xx.h"
+#include "km/km-mpc832x.h"
 
 #define CONFIG_SYS_MAMR		(MxMR_GPL_x4DIS | \
 				 0x0000c000 | \